1. 用戶應準備好加壓氣體及管路、驅動氣體及管路、高壓氣體出口管路，根據增壓泵出廠時提供的說明書固定增壓泵，并根據增壓泵進出口接頭的尺寸連接管路；檢查耐壓是否足夠，接頭是否漏水等。檢查完好后，即可進行加壓試驗。

1. Users should prepare pressurized gas and pipelines, drive gas and pipelines, high-pressure gas outlet pipelines, fix the booster pump according to the instructions provided at the factory, and connect pipelines according to the size of the inlet and outlet joints of the booster pump; Check if the pressure resistance is sufficient and if the joint is leaking water. After inspection, the pressure test can be carried out.

2. 氣源：氣體增壓泵驅動氣源的壓力范圍一般為1.8-8bar，不建議其驅動氣源超過10bar。如果驅動氣源過高，會(huì )對泵體造成很大程度的損壞，甚對操作人員造成傷害。

2. Gas source: The pressure range of the driving gas source for the gas booster pump is generally 1.8-8 bar, and it is not recommended that the driving gas source exceed 10 bar. If the driving air source is too high, it will cause significant damage to the pump body and even harm the operators.

3. 氣體增壓泵選型：客戶要根據自己的壓力需求選擇相應的增壓比，并根據自己的壓力需求突出氣源壓力、入口壓力、輸出壓力需求和流量，讓技術人員更準確的幫您選型。

3. Gas booster pump selection: Customers should choose the corresponding boost ratio based on their pressure requirements, and highlight the gas source pressure, inlet pressure, output pressure requirements, and flow rate according to their pressure requirements, so that technical personnel can more accurately help you choose.

4. 對于現場使用環境：現場使用環境必須干凈，不能有太大的塵粒，驅動氣源和加壓介質的含水量不能太高，否則會(huì )大大降低泵的使用壽命。

4. For on-site use environment: The on-site use environment must be clean, without too large dust particles, and the water content of the driving gas source and pressure medium should not be too high, otherwise it will greatly reduce the service life of the pump.

5. 對管道的要求：客戶現場使用時，必須檢查高壓輸出管道的密封性，使用的管道、閥門、壓力表必須大于氣體增壓泵輸出的額定壓力，以確保人員。

5. Requirements for pipelines: When customers use them on site, the sealing of the high-pressure output pipeline must be checked. The pipelines, valves, and pressure gauges used must be greater than the rated pressure output by the gas booster pump to ensure personnel safety.

6. 對壓力容器的要求：所有承壓部件，尤其是壓力容器，必須有壓力容器制造廠出具的壓力容器檢驗報告。

6. Requirements for pressure vessels: All pressure components, especially pressure vessels, must have a pressure vessel inspection report issued by the pressure vessel manufacturer.

更多的關于氣體增壓泵的問題或者詳細的內容，請進入我們公司的網站： http://www.liqun518.com網站中會(huì )有很多的內容僅供參考。

For more questions or detailed information about gas booster pumps, please visit our company's website: http://www.liqun518.com There will be a lot of content on the website for reference only.